生产线包括：

1.管道传送架：

12000*1600       5个    每架七组传送轮

              7500*1600        1个         每架五组传送轮

              800*1600         6个         每架一组传送轮

以上采用180#槽钢焊接，钢板采用8㎜和6㎜的。轮胎采用充气轮胎，传动部分采用五十铃传动轴连接，动力部分采用5.5KW*7台电机，变频调速，知名厂家减速机。                                                 

2、除锈机：

主箱体采用8㎜厚钢板，框架部分采用180#槽钢焊接，内部护板采用10㎜厚高鉻材质护板，抛头用高效抛头。 动力部分采用2*37KW电机，提升部分采用3KW电机带摆线针式减速机垂直皮带提升机。除尘装置采用二级除尘，一次为旋风除尘器，二次为布袋式除尘器。配二台4KW风机。

3、中频电源加热：

          配置250KW、500KW二台中频加热设备。250KW用于除锈机前，除去钢管表面水分，提高除锈效果。500KW用于外环氧粉末喷涂。采用专门设计的控制线路，保证钢管温度稳定。两台设备各带一个感应器，两条3.5米水电缆。

     500kw参数：

     250kw参数：

4、二次除锈装置：

清除管道外壁毛刺和附锈，动力为4KW，排尘动力为1.5KW。   

5.管道内除锈作业线：

         皮带供沙机长度15米，架空设置。动力为5.5KW 。喷砂罐采用四路喷砂，枪长12M,

高耐磨枪头。行走小车动力3KW,轨道架采用120#槽钢焊接，长度17M,宽度1.3M。

6．管道内喷液体涂料作业线（单、双组份）:

     单、双组份涂料采用一条生产线，行走小车为平板车，便于更换料桶。小车动力

为3KW，行走架采用100#槽钢焊接，长度为15M,宽度为1.2M。（单、双组份枪头、料桶、

喷涂机及料管甲方自备）。

7．放管平台：

三个放管平台总长72M，由甲方制作。

Ф 79 —Ф 630 derusting and anti-corrosion production line

 the production line comprising:

1. Pipe conveyor:

12000*1600 5 sets  seven sets of transfer wheels

7500*1600 1 set   five sets of transfer wheels

800*1600 6 sets   transfer wheels per set

The above is welded with 180# channel steel, and the steel plates are 8 mm and 6 mm. The tires are made of pneumatic tires, the transmission part is connected by Isuzu drive shaft, the power part is 5.5KW*7 sets of motors, frequency conversion speed regulation, well-known factory reducer.

2 , descaling machine:

The main box is made of 8mm thick steel plate, the frame part is welded with 180# channel steel, the inner guard plate is made of 10 mm thick high-chromium material, and the head is made of high-efficiency throwing head. The power part adopts 2*37KW motor, and the lifting part adopts 3KW motor with cycloidal pin reducer vertical belt hoist. The dust removal device adopts two-stage dust removal, one is a cyclone dust collector, and the second is a bag filter. Equipped with two 4KW fans.

3 , medium frequency power supply heating:

It is equipped with two medium frequency heating equipments of 250KW and 500KW . Before using 250KW for the descaling machine, remove the surface moisture of the steel pipe and improve the descaling effect. 500KW is used for external epoxy powder coating. The specially designed control circuit is used to ensure the temperature of the steel pipe is stable. Both units have one sensor and two 3.5 m water cables.

     500kw parameters:

250kw parameters:

4 , secondary descaling device:

The burr and rust of the outer wall of the pipeline are removed, the power is 4KW , and the dust driving power is 1.5KW .

5. Pipeline derusting line:

The belt sanding machine is 15 meters long and has an overhead setting. The power is 5.5KW . The sandblasting tank adopts four-way sandblasting with a gun length of 12M.

Highly wearable tips. The driving power of the trolley is 3KW, and the rail frame is welded by 120# channel steel, with a length of 17M and a width of 1.3M .

6 . Pipeline spray liquid coating line (single and double components ) :

     The single and double component coatings use one production line, and the walking trolley is a flatbed truck, which is convenient for replacing the material bucket. Car power

For 3KW , the walking frame is welded with 100# channel steel, the length is 15M and the width is 1.2M . (single and double component tips, buckets,

Spraying machine and material pipe are provided by Party A).

7 . Pipeline platform:

The total length of the three release platforms is 72M , which is produced by Party A.