Hot search: 3KW electromag
Aluminum ingot
1T one belt tw
2T steel melt
Detailed description of the ladle:
Steel ladle use
The ladle is used for casting in the foundry. After the iron is taken in front of the furnace, it is transported to the mold for pouring.
Steel water bag main selection method
1. Hanging bag form, two-way rotary type.
2, the form of gearbox, double worm gear drive.
3, speed ratio
4, the size
Main parameters and price of ladle
This price is for reference only. Contact us will have a very low price, please consult the specific price. firsTfurnace@gmail.com
CB manual, electric ladle technical parameters
GB manual, electric ladle technical parameters:
Executive Standard JB/T6685-2006
specification | Upper diameterΦ1（mm） | Lower mouth diameterΦ2（mm） | Bucket heightH（mm） | widthA（mm） | heighB（mm） |
GB-0.5 | 644 | 584 | 740 | 1230 | 1600 |
GB-1 | 770 | 710 | 880 | 1320 | 1955 |
GB-1.5 | 870 | 780 | 1000 | 1425 | 2150 |
GB-2 | 950 | 850 | 1100 | 1560 | 2210 |
GB-2.5 | 1040 | 940 | 1160 | 1615 | 2430 |
GB-3 | 1132 | 1088 | 1188 | 1688 | 2530 |
GB-4 | 1224 | 1104 | 1300 | 1710 | 2700 |
GB-5 | 1293 | 1173 | 1350 | 1880 | 2865 |
GB-6 | 1408 | 1268 | 1400 | 1980 | 3275 |
GB-7 | 1479 | 1337 | 1535 | 2215 | 3392 |
GB-8 | 1550 | 1400 | 1675 | 2450 | 3510 |
GB-10 | 1629 | 1469 | 1750 | 2530 | 3680 |
GB-12 | 1720 | 1550 | 1878 | 2565 | 3850 |
GB-15 | 1855 | 1675 | 1950 | 2600 | 4020 |
GB-20 | 1985 | 1785 | 2150 | 2785 | 4560 |
GB-25 | 2110 | 1900 | 2385 | 2888 | 4900 |
GB-30 | 2204 | 1984 | 2520 | 2960 | 5070 |
GB-40 | 2525 | 2257 | 2655 | ||
GB-50 | 2673 | 2387 | 2863 | ||
GB-60 | 2815 | 2516 | 3015 | ||
GB-70 | 3001 | 2606 | 3288 | ||
GB-80 | 3123 | 2711 | 3435 | ||
GB-90 | 3248 | 2820 | 3571 | ||
GB-100 | 3358 | 2915 | 3693 |
Ladle features
1. Reasonable selection of the center of rotation, easy to operate, basically can be re-created after pouring.
2, the use of double worm gear drive. Although the manufacturing requirements are high, the transmission is flexible and the two-way reversibility is good.
3. The lifting rod is made of forging, which is safer and safer than steel welded parts.
4. The body plate is thicker, and the bottom structure adopts triple insurance with combination of taper, bottom hoop and welding, which prolongs the service life and ensures the safety of the operator.
5, the main body and the boom, reducer and hand wheel, are equipped with a chain card can be locked at any time.
6. The two trunnions and the boom are equipped with self-aligning bearings, and the consistency is good.
Use and maintenance of ladle
1. refractory mud, the thickness of which is:
0.5 ton to 3 tons side wall 60 mm bottom 80 mm ;
5 tons of side walls 80 mm bottom 100 mm;
10 tons of side wall 100 mm bottom 120 mm;
More than 10 tons of sidewalls 150 mm bottom mm;
2. Check the handwheel, it should be free and free of jamming.
3, in the two trunnion rolling bearings, add molybdenum disulfide grease once a week.
4. Check if the handwheel locks the card board safely and reliably.
5. Check if there is any oil shortage in the gearbox and check it once a week.
6. After using for a long time, it is found that the worm gear pair gap is increased, and the worm gear pair should be replaced when it is difficult to safely pour.
PREV：No More Articles.
NEXT：Insulation ladle
Copyright© 2007-2013 NO.6 Electric Mall All Rights Reserved
