Ds-2000 Induction Heater-Hub Heater

Introduce：Ds-2000 induction heater - hub heater, induction heater, hub heater product details, technical performance, product advantages, operating instructions

Consultation

Related Products

Related Pictures

Introduction

Consultation

Detailed introduction

name:	Ds- 2000 induction heater
power:	200KVA
Voltage and current:	380V/520A
Adapt to the inner diameter of the workpiece:	φ > 300mm
Maximum workpiece outer diameter:	4000mm
Maximum workpiece width:	1000mm
Maximum workpiece load:	20000KG
Machine quality:	4000KG
Dimensions:	360×120×200cm
Heating rod configuration:	200mm

Ds -2000 Series

power	200 KVA	temperature control	0 - 240 ° C	Free warranty	3 years
Voltage	380V / 50Hz	time control	0 - 99'59''	time control	Have
Current	520A	Rotating device	Yes	Continuous installation	Have
Adapt to bearing inner diameter	φ >300mm	Horizontal heating bracket	Have	Temperature retention	Have
Maximum bearing outer diameter	4000mm	Movable	Yes	Automatic demagnetization	Have
Maximum bearing width	1000mm	Magnetic temperature probe	Yes	Automatic power reduction	Have
Maximum bearing weight(Kg)	20000	Column height	1000mm	Control panel (display )	digital
Other parts(Kg)	3000	Column size(mm)	300×1000	Heating rod standard	200×200( mm )
Host weight	4000Kg	Dimensions(cm)	360×120×200	Heating rod standard	200×200( mm )

I. Overview

This product is used in conjunction with metal parts. Using the principle of thermal expansion and contraction, the metal parts are heated to an aperture sufficient to easily reach the axial position without causing any damage to the workpiece or the shaft.

The whole process of heating the workpiece to the workpiece is controlled by a microcomputer. Safe, reliable, efficient, easy to use, and set three operating modes (time control mode, temperature control mode and temperature hold mode) for the operator to choose.

Second, technical performance

(1) Working conditions

1 , the power supply voltage exchange 380 ( V )

2 , the maximum working current is 520 amps ( A )

3 , working frequency 50 ~ 60 Hz ( Hz )

4 , power 200.0KVA

(2) Working mode and advantages

1. Temperature control mode, set the measurement range from 0 to 240 °C.

2 , time control mode, set the measurement range 0~99 minutes and 59 seconds.

3. Temperature hold: Press the temperature hold button to enter the temperature hold state when the heated workpiece reaches the set temperature.

4. This product has the function of soft start during operation, which reduces the impact on the device during start-up and prolongs the service life; when the power is off, the soft stop mode is adopted to realize the function of automatically removing the residual magnetism of the workpiece.

(3) Digital display and audio prompts

1. Temperature setting, the heating device preset temperature value is 110 °C.

2. The time setting can be set arbitrarily within 99 minutes and 59 seconds.

3. At the end of each heating cycle, there is an audio signal prompt.

4. When the sensor is not working normally, the device has an audio signal prompt.

(4) Heating the workpiece range

Heating workpiece inner diameter > 300mm

Heating workpiece outer diameter < 4000mm

Heating workpiece maximum thickness 1000mm

Third, the operating instructions

1. Ensure that the power supply voltage is accurate.

2. Plug the unit's power plug into a power outlet. When the switch on the side of the machine casing is turned on, the digital tube lights up and the temperature is 110 °C. At this time, the heating device is in the temperature control mode.

3. Press ▲▼ key to select the temperature value of the workpiece to be heated.

4. Press the START button to start the heating device to heat the heated workpiece.

5. When the heating device works to the set temperature value, the device will automatically stop and have an audible prompt.

6. If the temperature hold function is required , just press the temperature to keep it before proceeding to the fourth operation.

7. If the time control mode is adopted, the time control mode can be entered by pressing the button after power on, and the time setting value can be arbitrarily selected within 99 minutes and 59 seconds. Press ▲▼ key to select the heating time for the workpiece. Press the START button to start the heating deviceafter the selected time . This timing method is countdown. When the heating device is operated for a set time, there is an audible prompt and it automatically stops. (Time setting method: press the key once to enter the "seconds" is set, press the key twice to enter the "minute" setting each press "▲ ▼" key once, to increase or decrease the clock 1, and hold. Do not move, the clock changes continuously.)

8. When using the time control mode, there is no need to use the temperature sensor. In this case, the temperature sensor should be removed from the workpiece to prolong the service life of the sensor.

Fourth, matters needing attention

1 , can only be used at 380V voltage.

2. It is strictly forbidden to start the heating device with no load.

3. Make sure the cap is in place before pressing START .

4. When using the temperature control mode, the sensor should be reliably adsorbed on the inside of the workpiece, and the contact surface should be kept clean. If the E03 prompt appears: Please check if the sensor is connected or the workpiece is too large; if repeated prompts: Please check if the sensor is damaged.

5. Items that are susceptible to magnetic fields should be kept away. For example, cardiac pacemakers, hearing aids, magnetic tapes, magnetic cards, etc., the safety distance is 2 meters.

Understand Wikipedia： induction heating

ALL GATEGORIES

Ds-2000 Induction Heater-Hub Heater