DM-1000steam turbine guardring induction heater

Introduce：DM-1000 Turbine retaining ring induction heater, DM-1000 induction heater, induction heater product description, technical performance, product advantages, operating instructions

Consultation

Related Products

Related Pictures

Introduction

Consultation

Detailed introduction

name:	DM-1000 induction heater
power:	100KVA
Voltage and current:	380V/263A
Adapt to the inner diameter of the bearing:	φ > 145mm
Maximum bearing outer diameter:	2500mm
Maximum bearing width:	700mm
Maximum bearing load:	customizable
Machine quality:	2250 Kg
Dimensions:	220×70×120 cm
Heating rod configuration:	100,150,200 mm

DM-1000 parameter table

power	100 KVA	temperature control	0 - 240 ° C	heating method	Induction heating
Voltage	380V / 50Hz	time control	0 - 99'59''	time control	Have
Current	263A	Heating rod moving method	electric	Continuous installation	Have
Adapt to bearing inner diameter	φ > 145mm	Horizontal heating bracket	Have	Temperature retention	Have
Maximum bearing outer diameter	2500mm	Movable	Yes	Automatic demagnetization	Have
Maximum bearing width	700mm	Magnetic temperature probe	Yes	Automatic power reduction	Have
Maximum bearing weight(Kg)	customizable	Column height	780mm	Control panel (display )	digital
Other parts(Kg)	1600	Column size(mm)	200×200	Heating rod standard	200×200 (mm )
Host weight	2250 Kg	Dimensions(cm)	220×70×120	Heating rod matching	100×100 (mm ) 150×150 (mm )

I. Overview

This product is used in conjunction with metal parts. Using the principle of thermal expansion and contraction, the metal parts are heated to an aperture sufficient to easily reach the axial position without causing any damage to the workpiece or the shaft.

The whole process of heating the workpiece to the workpiece is controlled by a microcomputer. Safe, reliable, efficient, easy to use, and set three operating modes (time control mode, temperature control mode and temperature hold mode) for the operator to choose.

Second, technical performance

(1) Working conditions

1 , the power supply voltage exchange 380 ( V )

2 , the maximum working current 263 amps ( A )

3 , working frequency 50 ~ 60 Hz ( Hz )

4 , power 100.0KVA

(2) Working mode and advantages

1. Temperature control mode, set the measurement range from 0 to 240 °C.

2 , time control mode, set the measurement range 0~99 minutes and 59 seconds.

3. Temperature hold: Press the temperature hold button to enter the temperature hold state when the heated workpiece reaches the set temperature.

4. This product has the function of soft start during operation, which reduces the impact on the device during start-up and prolongs the service life; when the power is off, the soft stop mode is adopted to realize the function of automatically removing the residual magnetism of the workpiece.

(3) Digital display and audio prompts

1. Temperature setting, the heating device preset temperature value is 110 °C.

2. The time setting can be set arbitrarily within 99 minutes and 59 seconds.

3. At the end of each heating cycle, there is an audio signal prompt.

4. When the sensor is not working normally, the device has an audio signal prompt.

(4) Heating the workpiece range

Heating the inner diameter of the workpiece > 145mm

Maximum workpiece outer diameter > 2500mm

Heating workpiece maximum thickness 700mm

Third, the operating instructions

1. Ensure that the power supply voltage is accurate.

2. Connect the input end of the heating device to the 380V two-phase power supply, turn on the power switch of the device, and the digital tube lights up to display the temperature of 110 °C. At this time, the heating device is in the temperature control mode.

3. Press ▲▼ key to select the temperature value of the workpiece to be heated.

4. Press the START button to start the heating device to heat the heated workpiece.

5. When the heating device works to the set temperature value, the device will automatically stop and have an audible prompt.

6. If the temperature hold function is required , just press the temperature to keep it before proceeding to the fourth operation.

7. If the time control mode is adopted, the time control mode can be entered by pressing the button after power on, and the time setting value can be arbitrarily selected within 99 minutes and 59 seconds. Press ▲▼ key to select the heating time for the workpiece. Press the START button to start the heating deviceafter the selected time . This timing method is countdown. When the heating device is operated for a set time, there is an audible prompt and it automatically stops. (Time setting method: press the key once to enter the "seconds" is set, press the key twice to enter the "minute" setting each press "▲ ▼" key once, to increase or decrease the clock 1, and hold. Do not move, the clock changes continuously.)

8. When using the time control mode, there is no need to use the temperature sensor. In this case, the temperature sensor should be removed from the workpiece to prolong the service life of the sensor.

Fourth, matters needing attention

1 , can only be used at 380V voltage.

2. It is strictly forbidden to start the heating device with no load.

3. Make sure the cap is in place before pressing START .

4. When using the temperature control mode, the sensor should be reliably adsorbed on the inside of the workpiece, and the contact surface should be kept clean. If the E03 prompt appears: Please check if the sensor is connected or the workpiece is too large; if repeated prompts: Please check if the sensor is damaged.

5. Items that are susceptible to magnetic fields should be kept away. For example, cardiac pacemakers, hearing aids, magnetic tapes, magnetic cards, etc., the safety distance is 2 meters.

Understand Wikipedia： induction heating

ALL GATEGORIES

DM-1000steam turbine guardring induction heater